Wall Mounted Induction Loop Kit

Wall Mounted Induction Loop System for the Hearing Impaired

Wall Mounted Induction Loop Kit
  • Ideal for meeting rooms, lecture theatres, churches, schools, TV lounges, shops and other small to medium applications
  • Provides max. square room coverage 120m² (11m x 11m) or max. rectangular room coverage of 250m² (10m x 25m)
  • Straight forward internal screw connectors
  • Wall mountable for permanent installation – ideal for schools and colleges where rooms are often left unsupervised
  • Internal tamper-resistant drive, level and tone controls
  • One balanced/unbalanced microphone input
  • One balanced/unbalanced line level input
  • Alert tone switch input for doorbells, fire alarms, security systems, etc.
  • 100V line input for PA system connection
  • Fully automatic compressor-limiter
  • Full 2Ώ drive capability for increased coverage at higher frequencies
  • Compatible with SigNET’s unique ‘outreach plate’ input extension system
  • Available in a variety of formats to suit a host of typical loop installations
  • Fully compliant with EN60118-4 (formerly BS6083) and BS7594:1993

PDA200 induction loop kit

PDA200 induction loop kit

The PDA200Ehas revolutionised the induction loop marketplace by bringing the ability to understand, install and appreciate the technology involved to a whole new client base.

Straightforward internal screw connectors are required. By following the simple set-up procedure, no further adjustments are necessary, allowing a top quality assistive listening system for the hard of hearing to be set-up in its entirety by new and experienced installers alike.

No less than four easy-to-access inputs are provided:

  • Balanced/unbalanced mic (with phantom power for use with electret mics)
  • Balanced/unbalanced line (for connection of TV and other audio feeds)
  • Alert tone switch (a tone generator for use with doorbells, fire alarms, etc.)
  • 100V line (for connection of PA system audio feeds)

The amplifier’s state-of-the-art current drive audio processing circuitry includes an automatic compressor/ limiter, which maintains the loop signal within a small dynamic range to improve intelligibility. Manual adjustments can also be made using the amplifier’s internal tamper resistant drive, level and tone controls, allowing the system to be tailored to suit the exact requirements of any room.

For ease of specification and installation the PDA200E is available on its own or in the following kit formats:

AKM1 Meeting/seminar room kit

AKR1 Waiting room kit

AKT1 TV/music lounge kit

AKW1 Place of worship kit 1

AKW2 Place of worship kit 2

AKH1 Health and fitness club kit

AKL1 Lecture room kit

AKU1 Retail unit kit

PDA200 Induction loop kit

A typical PDA200E meeting/seminar room installation using items supplied in our AKM1 kit

The PDA200E requires fixed mains wiring fed from a 3A fused spur located no more than 3m from the amplifier
Mains voltage230vac
Power consumption<80VA
FusesInternal mains input fuse 1A 20mm (HRC)

Three 5mm screw connector inputs are available – mic., line & 100V. If more than one is used, the signals are mixed.

Input impedance600Ώ balanced/unbalanced
Sensitivity2-5mV (-46db to –50db)
Input impedance10k Ώ balanced/unbalanced
SensitivitySensitivity 0dbv
(300mV rms to 1.5V rms)
100V LINE:
Input impedance200k Ώ
Type:Current mode
Loop connector:Screw connector
Cable:1.0 – 2.5m2
Loop coverage (square room):120m2max. (e.g. 11 x 11m)
The PDA200E includes an amplitude compression stage that limits overload and has a dynamically variable ratio from 1:1 to 10:1
Bandwidth:40Hz to 8kHz
Input dynamic range:36dB
Distortion:<0.5% THD

DIMENSIONS: W:237mm x H:200mm x D:77mm
WEIGHT: 2.0kg (unpacked)


  • AKM1 – Meeting/seminar room kit: 1x PDA200E and 1x AMP Omni-directional plated microphone
  • AKR1 – Waiting room kit: 1x PDA200E and APL outreach plate (for connection of paging systems)
  • AKT1 – TV/music lounge kit: 1x PDA200E, 1x AMH handheld microphone c/w APJ outreach connection plate and 1x APS scart to dble phono lead c/w APL outreach plate (for connection of TVs, etc.)
  • AKL1 – Lecture room kit: 1x PDA200E, 1x AMT tie/desk microphone c/w APJ outreach connection plate and 1x AML lectern microphone c/w APJ outreach connection plate
  • AKW1 – Place of worship kit 1: 1x PDA200E, 1x AML lectern microphone c/w APJ outreach connection plate and 1x APL outreach plate (for connection of audio inputs from CD, tape decks, etc.)
  • AKW2 – Place of worhsip kit 2: 1x PDA100E, 1x AMR radio microphone c/w APQ outreach connection plate and 2x APXM outreach plate (for connection of existing microphones)
  • AKU1 – Retail unit kit: 1x PDA200E and 1x AML lectern microphone c/w APJ outreach connection plate.
  • AKH1 – Health and fitness club kit: 1x PDA200E, 1x AMR radio microphone c/w APQ outreach connection plate and 1x APL outreach plate (for connection of CD/tape decks, etc.)
LED indicators:Input peak (limit); output drive (1, 2, 3 peak current; power on (power)
User controls:One level control, adjustable between – 35dB to +0dB for both line and microphone
One output drive control, giving a loop current adjustable between 40mA and 2.1A
One mid-range cut & boost tone control (frequency = 1kHz; cut = 17dB; boost = +17db)

Enquire About This Product

SKU: wall-mounted-induction-loop-kit Category: Tags: , ,

Any Questions?

Our specialist team can advise on the best products to suit your needs. Just enter your number here and a member of our team will call you back to discuss which solutions are suitable for your requirements.